nxp,s32k3-pinctrl

Vendor: NXP Semiconductors

Description

NXP S32 pinctrl node for S32K3 SoCs.

The NXP S32 pin controller is a singleton node responsible for controlling
the pin function selection and pin properties. This node, labeled 'pinctrl' in
the SoC's devicetree, will define pin configurations in pin groups. Each group
within the pin configuration defines the pin configuration for a peripheral,
and each numbered subgroup in the pin group defines all the pins for that
peripheral with the same configuration properties. The 'pinmux' property in
a group selects the pins to be configured, and the remaining properties set
configuration values for those pins.

For example, to configure the pinmux for UART0, modify the 'pinctrl' from your
board or application devicetree overlay as follows:

  /* Include the SoC package header containing the predefined pins definitions */
  #include <nxp/s32/S32K344-257BGA-pinctrl.h>

  &pinctrl {
    uart0_default: uart0_default {
      group1 {
        pinmux = <PTA3_LPUART0_TX_O>;
        output-enable;
      };
      group2 {
        pinmux = <PTA28_LPUART0_RX>;
        input-enable;
      };
    };
  };

The 'uart0_default' node contains the pin configurations for a particular state
of a device. The 'default' state is the active state. Other states for the same
device can be specified in separate child nodes of 'pinctrl'.

In addition to 'pinmux' property, each group can contain other properties such as
'bias-pull-up' or 'slew-rate' that will be applied to all the pins defined in
'pinmux' array. To enable the input buffer use 'input-enable' and to enable the
output buffer use 'output-enable'.

To link the pin configurations with UART0 device, use pinctrl-N property in the
device node, where 'N' is the zero-based state index (0 is the default state).
Following previous example:

  &uart0 {
    pinctrl-0 = <&uart0_default>;
    pinctrl-names = "default";
    status = "okay";
  };

If only the required properties are supplied, the pin configuration register
will be assigned the following values:
  - input and output buffers disabled
  - internal pull not enabled
  - slew rate "fastest"
  - invert disabled
  - drive strength disabled.

Additionally, following settings are currently not supported and default to
the values indicated below:
  - Safe Mode Control (disabled)
  - Pad Keeping (disabled)
  - Input Filter (disabled).

Properties

Top level properties

These property descriptions apply to “nxp,s32k3-pinctrl” nodes themselves. This page also describes child node properties in the following sections.

Properties not inherited from the base binding file.

(None)

Grandchild node properties

Name

Type

Details

bias-disable

boolean

disable any pin bias

bias-pull-up

boolean

enable pull-up resistor

bias-pull-down

boolean

enable pull-down resistor

input-enable

boolean

enable input on pin (e.g. enable an input buffer, no effect on output)

output-enable

boolean

enable output on a pin without actively driving it (e.g. enable an output
buffer)

pinmux

array

An array of pins sharing the same group properties. The pins must be
defined using the S32_PINMUX macros that encodes all the pin muxing
information in a 32-bit value.

This property is required.

slew-rate

string

Slew rate control. Can be either slowest or fastest setting.
See the SoC reference manual for applicability of this setting.

Default value: fastest

Legal values: 'fastest', 'slowest'

nxp,invert

boolean

Invert the signal selected by Source Signal Selection (SSS) before
transmitting it to the associated destination (chip pin or module port).

nxp,drive-strength

boolean

Drive strength enable.
See the SoC reference manual for applicability of this setting.