New USB device support

Overview

USB device support consists of the USB device controller (UDC) drivers , USB device controller (UDC) driver API, and USB device stack, USB device stack (next) API. The USB device controller (UDC) driver API provides a generic and vendor independent interface to USB device controllers, and although, there a is clear separation between these layers, the purpose of USB device controller (UDC) driver API is to serve new Zephyr’s USB device stack exclusively.

The new device stack supports multiple device controllers, meaning that if a SoC has multiple controllers, they can be used simultaneously. Full and high-speed device controllers are supported. It also provides support for registering multiple function or class instances to a configuration at runtime, or changing the configuration later. It has built-in support for several USB classes and provides an API to implement custom USB functions.

The new USB device support is considered experimental and will replace USB device support.

Samples

Samples ported to new USB device support

To build a sample that supports both the old and new USB device stack, set the configuration -DCONF_FILE=usbd_next_prj.conf either directly or via west.

How to configure and enable USB device support

For the USB device support samples in the Zephyr project repository, we have a common file for instantiation, configuration and initialization, samples/subsys/usb/common/sample_usbd_init.c. The following code snippets from this file are used as examples. USB Samples Kconfig options used in the USB samples and prefixed with SAMPLE_USBD_ have default values specific to the Zephyr project and the scope is limited to the project samples. In the examples below, you will need to replace these Kconfig options and other defaults with values appropriate for your application or hardware.

The USB device stack requires a context structure to manage its properties and runtime data. The preferred way to define a device context is to use the USBD_DEVICE_DEFINE macro. This creates a static usbd_context variable with a given name. Any number of contexts may be instantiated. A USB controller device can be assigned to multiple contexts, but only one context can be initialized and used at a time. Context properties must not be directly accessed or manipulated by the application.

/*
 * Instantiate a context named sample_usbd using the default USB device
 * controller, the Zephyr project vendor ID, and the sample product ID.
 * Zephyr project vendor ID must not be used outside of Zephyr samples.
 */
USBD_DEVICE_DEFINE(sample_usbd,
		   DEVICE_DT_GET(DT_NODELABEL(zephyr_udc0)),
		   ZEPHYR_PROJECT_USB_VID, CONFIG_SAMPLE_USBD_PID);

Your USB device may have manufacturer, product, and serial number string descriptors. To instantiate these string descriptors, the application should use the appropriate USBD_DESC_MANUFACTURER_DEFINE, USBD_DESC_PRODUCT_DEFINE, and USBD_DESC_SERIAL_NUMBER_DEFINE macros. String descriptors also require a single instantiation of the language descriptor using the USBD_DESC_LANG_DEFINE macro.

USBD_DESC_LANG_DEFINE(sample_lang);
USBD_DESC_MANUFACTURER_DEFINE(sample_mfr, CONFIG_SAMPLE_USBD_MANUFACTURER);
USBD_DESC_PRODUCT_DEFINE(sample_product, CONFIG_SAMPLE_USBD_PRODUCT);
USBD_DESC_SERIAL_NUMBER_DEFINE(sample_sn);

String descriptors must be added to the device context at runtime before initializing the USB device with usbd_add_descriptor().

err = usbd_add_descriptor(&sample_usbd, &sample_lang);
if (err) {
	LOG_ERR("Failed to initialize language descriptor (%d)", err);
	return NULL;
}

err = usbd_add_descriptor(&sample_usbd, &sample_mfr);
if (err) {
	LOG_ERR("Failed to initialize manufacturer descriptor (%d)", err);
	return NULL;
}

err = usbd_add_descriptor(&sample_usbd, &sample_product);
if (err) {
	LOG_ERR("Failed to initialize product descriptor (%d)", err);
	return NULL;
}

err = usbd_add_descriptor(&sample_usbd, &sample_sn);
if (err) {
	LOG_ERR("Failed to initialize SN descriptor (%d)", err);
	return NULL;
}

USB device requires at least one configuration instance per supported speed. The application should use USBD_CONFIGURATION_DEFINE to instantiate a configuration. Later, USB device functions are assigned to a configuration.

static const uint8_t attributes = (IS_ENABLED(CONFIG_SAMPLE_USBD_SELF_POWERED) ?
				   USB_SCD_SELF_POWERED : 0) |
				  (IS_ENABLED(CONFIG_SAMPLE_USBD_REMOTE_WAKEUP) ?
				   USB_SCD_REMOTE_WAKEUP : 0);

/* Full speed configuration */
USBD_CONFIGURATION_DEFINE(sample_fs_config,
			  attributes,
			  CONFIG_SAMPLE_USBD_MAX_POWER, &fs_cfg_desc);

/* High speed configuration */
USBD_CONFIGURATION_DEFINE(sample_hs_config,
			  attributes,
			  CONFIG_SAMPLE_USBD_MAX_POWER, &hs_cfg_desc);

Each configuration instance for a specific speed must be added to the device context at runtime before the USB device is initialized using usbd_add_configuration(). Note USBD_SPEED_FS and USBD_SPEED_HS. The first full-speed or high-speed configuration will get bConfigurationValue one, and then further upward.

err = usbd_add_configuration(&sample_usbd, USBD_SPEED_FS,
			     &sample_fs_config);
if (err) {
	LOG_ERR("Failed to add Full-Speed configuration");
	return NULL;
}

Although we have already done a lot, this USB device has no function. A device can have multiple configurations with different set of functions at different speeds. A function or class can be registered on a USB device before it is initialized using usbd_register_class(). The desired configuration is specified using USBD_SPEED_FS or USBD_SPEED_HS and the configuration number. For simple cases, usbd_register_all_classes() can be used to register all available instances.

err = usbd_register_all_classes(&sample_usbd, USBD_SPEED_FS, 1);
if (err) {
	LOG_ERR("Failed to add register classes");
	return NULL;
}

The last step in the preparation is to initialize the device with usbd_init(). After this, the configuration of the device cannot be changed. A device can be deinitialized with usbd_shutdown() and all instances can be reused, but the previous steps must be repeated. So it is possible to shutdown a device, register another type of configuration or function, and initialize it again. At the USB controller level, usbd_init() does only what is necessary to detect VBUS changes. There are controller types where the next step is only possible if a VBUS signal is present.

A function or class implementation may require its own specific configuration steps, which should be performed prior to initializing the USB device.

err = usbd_init(&sample_usbd);
if (err) {
	LOG_ERR("Failed to initialize device support");
	return NULL;
}

The final step to enable the USB device is usbd_enable(), after that, if the USB device is connected to a USB host controller, the host can start enumerating the device. The application can disable the USB device using usbd_disable().

ret = usbd_enable(sample_usbd);
if (ret) {
	LOG_ERR("Failed to enable device support");
	return ret;
}

USB Message notifications

The application can register a callback using usbd_msg_register_cb() to receive message notification from the USB device support subsystem. The messages are mostly about the common device state changes, and a few specific types from the USB CDC ACM implementation.

err = usbd_msg_register_cb(&sample_usbd, msg_cb);
if (err) {
	LOG_ERR("Failed to register message callback");
	return NULL;
}

The helper function usbd_msg_type_string() can be used to convert usbd_msg_type to a human readable form for logging.

If the controller supports VBUS state change detection, the battery-powered application may want to enable the USB device only when it is connected to a host. A generic application should use usbd_can_detect_vbus() to check for this capability.

static void msg_cb(struct usbd_context *const usbd_ctx,
		   const struct usbd_msg *const msg)
{
	LOG_INF("USBD message: %s", usbd_msg_type_string(msg->type));

	if (msg->type == USBD_MSG_CONFIGURATION) {
		LOG_INF("\tConfiguration value %d", msg->status);
	}

	if (usbd_can_detect_vbus(usbd_ctx)) {
		if (msg->type == USBD_MSG_VBUS_READY) {
			if (usbd_enable(usbd_ctx)) {
				LOG_ERR("Failed to enable device support");
			}
		}

		if (msg->type == USBD_MSG_VBUS_REMOVED) {
			if (usbd_disable(usbd_ctx)) {
				LOG_ERR("Failed to disable device support");
			}
		}
	}
}

Built-in functions

The USB device stack has built-in USB functions. Some can be used directly in the user application through a special API, such as HID or Audio class devices, while others use a general Zephyr RTOS driver API, such as MSC and CDC class implementations. The Identification string identifies a class or function instance (n) and is used as an argument to the usbd_register_class().

Class or function

User API (if any)

Identification string

USB Audio 2 class

Audio Class 2 device API

uac2_n

USB CDC ACM class

Universal Asynchronous Receiver-Transmitter (UART)

cdc_acm_n

USB CDC ECM class

Ethernet device

cdc_ecm_n

USB Mass Storage Class (MSC)

USB Mass Storage Class device API

msc_n

USB Human Interface Devices (HID)

HID device API

hid_n

Bluetooth HCI USB transport layer

HCI RAW channel

bt_hci_n

CDC ACM UART

CDC ACM implements a virtual UART controller and provides Interrupt-driven UART API and Polling UART API.

Interrupt-driven UART API

Internally the implementation uses two ringbuffers, these take over the function of the TX/RX FIFOs (TX/RX buffers) from the Interrupt-driven API.

As described in the Interrupt-driven API, the functions uart_irq_update(), uart_irq_is_pending(), uart_irq_rx_ready(), uart_irq_tx_ready() uart_fifo_read(), and uart_fifo_fill() should be called from the interrupt handler, see uart_irq_callback_user_data_set(). To prevent undefined behaviour, the implementation of these functions checks in what context they are called and fails if it is not an interrupt handler.

Also, as described in the UART API, uart_irq_is_pending() uart_irq_rx_ready(), and uart_irq_tx_ready() can only be called after uart_irq_update().

Simplified, the interrupt handler should look something like:

static void interrupt_handler(const struct device *dev, void *user_data)
{
   while (uart_irq_update(dev) && uart_irq_is_pending(dev)) {
      if (uart_irq_rx_ready(dev)) {
         int len;
         int n;

         /* ... */
         n = uart_fifo_read(dev, buffer, len);
         /* ... */
      }

      if (uart_irq_tx_ready(dev)) {
         int len;
         int n;

         /* ... */
         n = uart_fifo_fill(dev, buffer, len);
        /* ... */
      }
}

All these functions are not directly dependent on the status of the USB device. Filling the TX FIFO does not mean that data is being sent to the host. And successfully reading the RX FIFO does not mean that the device is still connected to the host. If there is space in the TX FIFO, and the TX interrupt is enabled, uart_irq_tx_ready() will succeed. If there is data in the RX FIFO, and the RX interrupt is enabled, uart_irq_rx_ready() will succeed. Function uart_irq_tx_complete() is not implemented yet.

Polling UART API

The CDC ACM poll out implementation follows Polling API and blocks when the TX FIFO is full only if the hw-flow-control property is enabled and called from a non-ISR context.