Board specific Timing Measurement APIs

Board specific Timing Measurement APIs . More...

Functions
void	board_timing_init (void)
	Initialize the timing subsystem.
void	board_timing_start (void)
	Signal the start of the timing information gathering.
void	board_timing_stop (void)
	Signal the end of the timing information gathering.
timing_t	board_timing_counter_get (void)
	Return timing counter.
uint64_t	board_timing_cycles_get (volatile timing_t *const start, volatile timing_t *const end)
	Get number of cycles between start and end.
uint64_t	board_timing_freq_get (void)
	Get frequency of counter used (in Hz).
uint64_t	board_timing_cycles_to_ns (uint64_t cycles)
	Convert number of cycles into nanoseconds.
uint64_t	board_timing_cycles_to_ns_avg (uint64_t cycles, uint32_t count)
	Convert number of cycles into nanoseconds with averaging.
uint32_t	board_timing_freq_get_mhz (void)
	Get frequency of counter used (in MHz).

Detailed Description

Board specific Timing Measurement APIs .

Implements the necessary bits to support timing measurement using board specific timing measurement mechanism.

Function Documentation

board_timing_counter_get()

timing_t board_timing_counter_get

(

void

)

#include <zephyr/timing/timing.h>

Return timing counter.

Note

Not all timing counters have 64 bit precision. It is possible to see this value "go backwards" due to internal rollover. Timing code must be prepared to address the rollover (with board dependent code, e.g. by casting to a uint32_t before subtraction) or by using board_timing_cycles_get() which is required to understand the distinction.

Returns

Timing counter.

See also

timing_counter_get()

board_timing_cycles_get()

uint64_t board_timing_cycles_get	(	volatile timing_t *const	start,
		volatile timing_t *const	end )

#include <zephyr/timing/timing.h>

Get number of cycles between start and end.

Note

The raw numbers from counter need to be scaled to obtain actual number of cycles, or may roll over internally. This function computes a positive-definite interval between two returned cycle values.

Parameters

start	Pointer to counter at start of a measured execution.
end	Pointer to counter at stop of a measured execution.

Returns

Number of cycles between start and end.

See also

timing_cycles_get()

board_timing_cycles_to_ns()

uint64_t board_timing_cycles_to_ns

(

uint64_t

cycles

)

#include <zephyr/timing/timing.h>

Convert number of cycles into nanoseconds.

Parameters

cycles

Number of cycles

Returns

Converted time value

See also

timing_cycles_to_ns()

board_timing_cycles_to_ns_avg()

uint64_t board_timing_cycles_to_ns_avg	(	uint64_t	cycles,
		uint32_t	count )

#include <zephyr/timing/timing.h>

Convert number of cycles into nanoseconds with averaging.

Parameters

cycles	Number of cycles
count	Times of accumulated cycles to average over

Returns

Converted time value

See also

timing_cycles_to_ns_avg()

board_timing_freq_get()

uint64_t board_timing_freq_get

(

void

)

#include <zephyr/timing/timing.h>

Get frequency of counter used (in Hz).

Returns

Frequency of counter used for timing in Hz.

See also

timing_freq_get()

board_timing_freq_get_mhz()

uint32_t board_timing_freq_get_mhz

(

void

)

#include <zephyr/timing/timing.h>

Get frequency of counter used (in MHz).

Returns

Frequency of counter used for timing in MHz.

See also

timing_freq_get_mhz()

board_timing_init()

void board_timing_init

(

void

)

#include <zephyr/timing/timing.h>

Initialize the timing subsystem.

Perform the necessary steps to initialize the timing subsystem.

See also

timing_init()

board_timing_start()

void board_timing_start

(

void

)

#include <zephyr/timing/timing.h>

Signal the start of the timing information gathering.

Signal to the timing subsystem that timing information will be gathered from this point forward.

See also

timing_start()

board_timing_stop()

void board_timing_stop

(

void

)

#include <zephyr/timing/timing.h>

Signal the end of the timing information gathering.

Signal to the timing subsystem that timing information is no longer being gathered from this point forward.

See also

timing_stop()