Bluetooth Mesh: Light switch

The Bluetooth Mesh light switch sample can be used to change the state of light sources on other devices within the same mesh network. It also demonstrates how to use Bluetooth® Mesh models by using the Generic OnOff Client model in an application.

Use the light switch sample with the Bluetooth Mesh: Light sample to demonstrate its function in a Bluetooth Mesh network.

This sample also provides the Low Power node support.

Requirements

The sample supports the following development kits:

Hardware platforms

PCA

Board name

Board target

Thingy:53

PCA20053

thingy53

thingy53/nrf5340/cpuapp

nRF54L15 DK

PCA10156

nrf54l15dk

nrf54l15dk/nrf54l15/cpuapp

nRF5340 DK

PCA10095

nrf5340dk

nrf5340dk/nrf5340/cpuapp/ns nrf5340dk/nrf5340/cpuapp

nRF52 DK

PCA10040

nrf52dk

nrf52dk/nrf52832

nRF52840 DK

PCA10056

nrf52840dk

nrf52840dk/nrf52840

nRF52833 DK

PCA10100

nrf52833dk

nrf52833dk/nrf52833

nRF21540 DK

PCA10112

nrf21540dk

nrf21540dk/nrf52840

You need at least two development kits:

  • One development kit where you program this sample application (the client)

  • One (or more) development kit(s) where you program the Bluetooth Mesh: Light sample application (the server(s)), and configure according to the mesh light sample’s testing guide

For provisioning and configuring of the mesh model instances, the sample requires a smartphone with Nordic Semiconductor’s nRF Mesh mobile app installed in one of the following versions:

Note

If you build this application for Thingy:53, it enables additional features. See Application guide for Thingy:53 for details.

When built for a board target with the */ns variant, the sample is configured to compile and run as a non-secure application with Cortex-M Security Extensions enabled. Therefore, it automatically includes Trusted Firmware-M that prepares the required peripherals and secure services to be available for the application.

Low Power node requirements

The configuration overlay overlay-lpn.conf is optimized for the following boards:

  • nrf52dk/nrf52832

  • nrf52840dk/nrf52840

  • nrf52833dk/nrf52833

However, the same configuration can be applied to other platforms that support the Bluetooth Mesh Light Switch sample, as long as the device supports at least four buttons.

Overview

The Bluetooth Mesh light switch sample demonstrates how to set up a mesh client model application, and control LEDs with the Bluetooth Mesh using the Generic OnOff models. To display any functionality, the sample must be paired with a device with the Bluetooth Mesh: Light sample running in the same mesh network.

In both samples, devices are nodes with a provisionee role in a mesh network. Provisioning is performed using the nRF Mesh mobile app. This mobile application is also used to configure key bindings, and publication and subscription settings of the Bluetooth Mesh model instances in the sample to enable them to communicate with the servers.

The Generic OnOff Client model is used for manipulating the Generic OnOff state associated with the Generic OnOff Server model. The light switch sample implements the Generic OnOff Client model.

The sample instantiates up to four instances of the Generic OnOff Client model to control the state of LEDs on servers (implemented by the Bluetooth Mesh: Light sample). One instance of the Generic OnOff Client model is instantiated in the light switch sample for each button available on the development kit that is used. When a user presses any of the buttons, an OnOff Set message is sent out to the configured destination address.

After provisioning and configuring the mesh models supported by the sample using the nRF Mesh mobile app, you can control the LEDs on the other (server) development kit(s) from the app.

Provisioning

Provisioning is handled by the Bluetooth Mesh provisioning handler for Nordic DKs. It supports four types of out-of-band (OOB) authentication methods, and uses the Hardware Information driver to generate a deterministic UUID to uniquely represent the device.

Models

The following table shows the mesh light switch composition data for this sample:

Element 1

Element 2

Element 3

Element 4

Config Server

Gen. OnOff Client

Gen. OnOff Client

Gen. OnOff Client

Health Server

Gen. OnOff Client

Note

When used with Thingy:53, Elements 3 and 4 are not available. Thingy:53 supports only two buttons.

The models are used for the following purposes:

  • Generic OnOff Client instances in available elements are controlled by the buttons on the development kit.

  • Config Server allows configurator devices to configure the node remotely.

  • Health Server provides attention callbacks that are used during provisioning to call your attention to the device. These callbacks trigger blinking of the LEDs.

The model handling is implemented in src/model_handler.c, which uses the DK Buttons and LEDs library to detect button presses on the development kit.

If the model is configured to publish to a unicast address, the model handler calls bt_mesh_onoff_cli_set() to turn the LEDs of a mesh light device on or off. The response from the target device updates the corresponding LED on the mesh light switch device. If the model is configured to publish to a group address, it calls bt_mesh_onoff_cli_set_unack() instead, to avoid getting responses from multiple devices at once.

Low Power node support

The mesh light switch sample can also be run as a Low Power node (LPN), giving the possibility of lowering the power consumption.

While running the sample with the LPN configuration, the fourth Generic OnOff Client instance will be omitted. Instead, Button 4 will be used to temporarily enable Node ID advertisement on the LPN device.

Running continuous proxy advertisement with Network ID consumes considerable power, and is therefore disabled in the configuration. Instead, the user can manually enable the Node ID advertisement for a period of 30 seconds by pressing Button 4 on the device. This will give the user a short period of time to connect directly to the LPN, and thus perform necessary configuration of the device.

After the connection to the LPN is terminated, and the Node ID advertisement has stopped, the LPN will return to its previous state.

Friendship establishment will happen automatically after provisioning the LPN light switch, given that a Bluetooth Mesh: Light sample is running and is provisioned into the same mesh network.

Note

While running the sample as an LPN, logging over the serial interface will be disabled.

Power consumption measurements

The following table shows a list of the supported boards for the LPN configuration, the average power consumption running as a standard (non-LPN) node, and the average power consumption running as an LPN node:

Board

Avg. consumption non-LPN

Avg. consumption LPN

nrf52dk/nrf52832

7.14 mA

13.69 µA

nrf52840dk/nrf52840

6.71 mA

14.63 µA

nrf52833dk/nrf52833

6.10 mA

14.43 µA

The following applies to the LPN measurements presented in this table:

  • They are taken after the provisioning and configuration have completed, and after the LPN has established a friendship to a neighboring node.

  • The measurement period is approximately ten minutes, and without any light switch events (for example when idle).

  • The current consumption is measured using the Power Profiler Kit II (PPK2).

  • The measurements are done on the SoC only (meaning the measurements do not include power consumed by development kit LEDs for example).

Power consumption for nRF52840 running as standard node

Power consumption for nRF52840 running as standard node (Captured in nRF Connect for Desktop: Power Profiler).

Power consumption for nRF52840 running as LPN

Power consumption for nRF52840 running as LPN, showing consumed power over a single LPN polling period. The rightmost spike represents the LPN polling the friend node. (Captured in nRF Connect for Desktop: Power Profiler).

User interface

Buttons:

During the provisioning process, the buttons can be used for OOB input. Once the provisioning and configuration are completed, the buttons are used to initiate certain actions and control the respective Generic OnOff Client instances. When pressed, the button publishes an OnOff message using the configured publication parameters of its model instance, and toggles the LED state on a mesh light device.

LEDs:

During the provisioning process, on board LEDs are used to output the OOB actions. Once the provisioning and configuration are completed, the LEDs are used to reflect the status of actions, and they show the last known OnOff state of the corresponding button.

Note

Thingy:53 supports only one RGB LED. Each RGB LED channel is used as separate LED.

The LPN assignments

Button 4:

When pressed, enables the Node ID advertisement for a short period of time.

Configuration

See Configuring and building for information about how to permanently or temporarily change the configuration.

For nRF5340 and Thingy:53, the extended advertiser has to be set manually for the network core, because the Bluetooth® Low Energy does not know that the Bluetooth Mesh is enabled when built for this core. This is already done for this sample by setting CONFIG_BT_EXT_ADV=y for the network core.

Source file setup

The light switch sample is split into the following source files:

  • main.c used to handle initialization.

  • model_handler.c used to handle mesh models.

LPN configuration

To make the light switch run as an LPN, set EXTRA_CONF_FILE to overlay-lpn.conf when building the sample using the respective CMake option. For example, when building from the command line, use the following command, where board_target is the target for the development kit for which you are building:

west build -b board_target -p -- -DEXTRA_CONF_FILE="overlay-lpn.conf"

The configuration overlay overlay-lpn.conf enables the LPN feature, and alters certain configuration options to further lower the power consumption. To review the specific alterations, open and inspect the overlay-lpn.conf file.

For more information about configuration files in the nRF Connect SDK, see Build and configuration system.

FEM support

You can add support for the nRF21540 front-end module to this sample by using one of the following options, depending on your hardware:

  • Build the sample for one board that contains the nRF21540 FEM, such as nrf21540dk/nrf52840.

  • Manually create a devicetree overlay file that describes how the nRF21540 FEM is connected to the SoC. See Configuring devicetree for different ways of adding the overlay file.

  • Provide nRF21540 FEM capabilities by using a shield, for example the nRF21540 EK shield that is available in the nRF Connect SDK. In this case, build the project for a board connected to the shield you are using with an appropriate variable included in the build command, for example -DSHIELD=nrf21540ek. This variable instructs the build system to append the appropriate devicetree overlay file.

    To build the sample in the nRF Connect for VS Code extension for an nRF52840 DK with the nRF21540 EK attached, add the shield variable in the build configuration’s Extra CMake arguments and rebuild the build configuration. For example: -DSHIELD=nrf21540ek.

    See How to work with build configurations in the nRF Connect for VS Code extension documentation for more information.

    See Programming nRF21540 EK for information about how to program when you are using a board with a network core, for example the nRF5340 DK.

Each of these options adds the description of the nRF21540 FEM to the devicetree. See Developing with Front-End Modules for more information about FEM in the nRF Connect SDK.

To add support for other front-end modules, add the respective devicetree file entries to the board devicetree file or the devicetree overlay file.

Building and running

Make sure to enable the Bluetooth Mesh in nRF Connect SDK before building and testing this sample. See Bluetooth Mesh user guide for more information.

This sample can be found under samples/bluetooth/mesh/light_switch in the nRF Connect SDK folder structure.

When built as firmware image for a board target with the */ns variant, the sample has Cortex-M Security Extensions (CMSE) enabled and separates the firmware between Non-Secure Processing Environment (NSPE) and Secure Processing Environment (SPE). Because of this, it automatically includes the Trusted Firmware-M (TF-M). To read more about CMSE, see Processing environments.

To build the sample, follow the instructions in Building an application for your preferred building environment. See also Programming an application for programming steps and Testing and optimization for general information about testing and debugging in the nRF Connect SDK.

Note

When building repository applications in the SDK repositories, building with sysbuild is enabled by default. If you work with out-of-tree freestanding applications, you need to manually pass the --sysbuild parameter to every build command or configure west to always use it.

Testing

Note

The light switch sample cannot demonstrate any functionality on its own, and needs a device with the Bluetooth Mesh: Light sample running in the same mesh network. Before testing mesh light switch, go through the mesh light’s testing guide with a different development kit.

After programming the sample to your development kit, you can test it by using a smartphone with nRF Mesh mobile app installed. Testing consists of provisioning the device and configuring it for communication with the mesh models.

Provisioning the device

The provisioning assigns an address range to the device, and adds it to the mesh network. Complete the following steps in the nRF Mesh app:

  1. Tap Add node to start scanning for unprovisioned mesh devices.

  2. Select the Mesh Light Switch device to connect to it.

  3. Tap Identify, and then Provision, to provision the device.

  4. When prompted, select an OOB method and follow the instructions in the app.

Once the provisioning is complete, the app returns to the Network screen.

Configuring models

See Configuring Bluetooth Mesh models using the nRF Mesh mobile app for details on how to configure the mesh models with the nRF Mesh mobile app.

Note

When configuring mesh models using the nRF Mesh mobile app, make sure that you are connected directly to the Mesh Light Switch LPN when configuring the LPN. When using the mobile app for iOS, make sure that automatic proxy connection is disabled.

Configure the Generic OnOff Client model on each element on the Mesh Light Switch node:

  • Bind the model to Application Key 1.

  • Set the publication parameters:

    • Destination/publish address: Set the Publish Address to the first unicast address of the Mesh Light node.

    • Retransmit count: Set the count to zero (Disabled), to prevent the model from sending each button press multiple times.

Once the provisioning and the configuration of the client node and at least one of the server nodes are complete, you can use buttons on the client development kit. The buttons will control the LED lights on the associated servers, as described in User interface.

Dependencies

This sample uses the following nRF Connect SDK libraries:

In addition, it uses the following Zephyr libraries:

The sample also uses the following secure firmware component: