Bluetooth: nRF Distance Measurement with Bluetooth LE discovery

The nRF Distance Measurement sample demonstrates the functionality of the Distance Measurement (DM) subsystem. It shows how to use DM to measure the distance between devices. The Bluetooth® Direction and Distance Finding Service (DDFS) is running simultaneously.

Sample is configured to use Nordic’s SoftDevice link layer.

Note

The Distance Measurement support in the nRF Connect SDK is experimental. See Distance Measurement for details.

Requirements

The sample supports the following development kits:

Hardware platforms	PCA	Board name	Board target
nRF5340 DK	PCA10095	nrf5340dk	nrf5340dk/nrf5340/cpuapp
nRF52 DK	PCA10040	nrf52dk	nrf52dk/nrf52832
nRF52840 DK	PCA10056	nrf52840dk	nrf52840dk/nrf52840
nRF52833 DK	PCA10100	nrf52833dk	nrf52833dk/nrf52833

Overview

The sample initializes and performs distance measurements between devices. The procedure for distance measurement on both devices must be synchronized.

The synchronization step has two goals:

• Detect peers that support the ranging procedure.

• Provide synchronization for the ranging step.

This sample synchronizes devices using the scan and advertising facilities of the Bluetooth LE. Anchoring occurs after the exchange of SCAN_REQ and SCAN_RSP packets.

The following chart shows the sequence of the synchronization process:

Both devices act as an advertiser and a scanner. Device B receives advertising from Device A and scans it. Device A sends a scan response that contains Manufacturer Specific Data. This message contains the following fields:

• Company Identifier Code.

• Identifier indicating that the device supports distance measurement.

• The access address used for measurement.

This scanner/advertiser interaction is used as a synchronization point. After a configurable delay, Device A and Device B try to range each other.

• If a Device acts as an advertiser in synchronization, it will act as the reflector in the ranging procedure.

• If a Device acts as a scanner in synchronization, it will act as the initiator in the ranging procedure.

The synchronization is performed cyclically.

Based on the SCAN_RSP response, the device recognizes peers that support the distance measurement functionality within its coverage. The addresses of these devices are stored in a list. When a device does not respond within a certain period of time, it is removed from the list. Also, the last measurement results with the peers are stored in this list.

For the nRF5340, the ranging procedure is performed on the network core, while the calculation takes place on the application core. The distance calculation uses a floating-point unit (FPU).

Power consumption

Power consumption and the number of measurements performed in a given time depend on the following factors:

• Advertiser settings.

• Scanner settings.

• Extended size of measurement window by extra_window_time_us in the dm_request structure.

The shorter the advertising interval, the higher the frequency at which the broadcaster sends out advertising packages. This leads to a higher probability of synchronization and to a higher number of measurements taken at a given time. It also decreases the latency for the first measurement when the device is turned on or comes in reach. However, the higher number of packets transmitted also results in higher power consumption.

The scan interval and scan window parameters determine how often and how long the scanning device will listen for packets. Like the short advertising interval, these values also have an impact on power consumption and the ranging frequency of devices.

After the first measurement, the CONFIG_DM_MIN_TIME_BETWEEN_TIMESLOTS_US and the CONFIG_DM_TIMESLOT_QUEUE_COUNT_SAME_PEER Kconfig options define how often the same device is measured again. The Kconfig options CONFIG_DM_TIMESLOT_QUEUE_COUNT_SAME_PEER and CONFIG_DM_TIMESLOT_QUEUE_LENGTH define how many measurements are scheduled. The more measurements are scheduled, the more of them take place, which increases power consumption but gives more frequent rangings. If the CONFIG_DM_TIMESLOT_RESCHEDULE Kconfig option is disabled, the next timeslot for measurement execution will be allocated after the measurement request is added using the dm_request_add() function.

Extending the measurement window increases the probability of measurement success for coarse synchronization. However, it affects the turn-on time of the radio and thus, power consumption.

At the application runtime, the additional delay of measurement execution is configured using the start_delay_us parameter of the dm_request structure. This option helps in adjusting the synchronization. The CONFIG_DM_INITIATOR_DELAY_US Kconfig option defines the initiator delay. Increasing the values of these parameters increases the latency and power consumption.

High-precision calculation

The sample supports distance estimation using a more compute-intensive high-precision algorithm. The CONFIG_DM_HIGH_PRECISION_CALC Kconfig option enables high-precision calculations. High-precision calculation has an impact on MCPD ranging mode only. Due to its limited memory, the nRF52 Development Kit (nrf52dk_nrf52832) does not support high-precision calculations.

Zero-distance calibration

The measured values of distance measurement include an offset. The offset value may depend on the design of the radio circuit, the antenna used, or the PCB layout. When using a library and a sample, you need to compensate the zero-distance offset and perform the calibration manually. To determine the offset value, place the devices at a reference distance of 60 cm from each other and collect a batch of measurement data. The difference between the average measurement value and the actual distance can be used as an estimate of the offset.

User interface

LED 1:

Indicates the measured distance for MCPD (Multi-carrier phase difference) method. The shorter the distance, the brighter the light.

LED 2:

Blinks every two seconds with the duty cycle set to 50% when the main loop is running and the device is advertising.

LED 3:

Lit when connected.

Building and running

This sample can be found under samples/bluetooth/nrf_dm in the nRF Connect SDK folder structure.

To build the sample, follow the instructions in Building an application for your preferred building environment. See also Programming an application for programming steps and Testing and optimization for general information about testing and debugging in the nRF Connect SDK.

Note

When building repository applications in the SDK repositories, building with sysbuild is enabled by default. If you work with out-of-tree freestanding applications, you need to manually pass the --sysbuild parameter to every build command or configure west to always use it.

Testing

After programming the sample to development kits, test it by performing the following steps:

1. Connect to the kit that runs this sample with a terminal emulator (for example, nRF Connect Serial Terminal). See Testing and optimization for the required settings and steps.

2. Reset the kit.

3. Program the other development kit with the same sample and reset it.

4. Wait until the devices identify themselves and synchronize.

5. Observe that the received measurement results are output in the terminal window.

Sample output

The result should look similar to the following output:

• The MCPD method:

  *** Booting Zephyr OS build v2.6.99-ncs1  ***
  Starting Distance Measurement example
  I: SoftDevice Controller build revision:
  I: 3f 47 70 8e 81 95 4e 86 |?Gp...N.
  I: 9d d3 a2 95 88 f6 30 0a |......0.
  I: 7f 53 49 fd             |.SI.
  I: HW Platform: Nordic Semiconductor (0x0002)
  I: HW Variant: nRF52x (0x0002)
  I: Firmware: Standard Bluetooth controller (0x00) Version 63.28743 Build 1318420878
  I: Identity: C4:90:D5:4E:C2:20 (random)
  I: HCI: version 5.2 (0x0b) revision 0x125b, manufacturer 0x0059
  I: LMP: version 5.2 (0x0b) subver 0x125b
  DM Bluetooth LE Synchronization initialization
  
  Measurement result:
        Addr DB:49:E9:62:DF:6D (random)
        Quality ok
        Distance estimates: mcpd: ifft=0.29 phase_slope=0.28 rssi_openspace=0.28 best=0.29
  
  Measurement result:
        Addr CF:4E:38:D5:C0:ED (random)
        Quality ok
        Distance estimates: mcpd: ifft=0.94 phase_slope=1.10 rssi_openspace=0.22 best=0.94
  
  Measurement result:
        Addr CF:4E:38:D5:C0:ED (random)
        Quality ok
        Distance estimates: mcpd: ifft=0.79 phase_slope=1.08 rssi_openspace=0.25 best=0.79
  

• The RTT method:

  *** Booting Zephyr OS build v2.6.99-ncs1  ***
  Starting Distance Measurement example
  I: SoftDevice Controller build revision:
  I: 3f 47 70 8e 81 95 4e 86 |?Gp...N.
  I: 9d d3 a2 95 88 f6 30 0a |......0.
  I: 7f 53 49 fd             |.SI.
  I: HW Platform: Nordic Semiconductor (0x0002)
  I: HW Variant: nRF52x (0x0002)
  I: Firmware: Standard Bluetooth controller (0x00) Version 63.28743 Build 1318420878
  I: Identity: C4:90:D5:4E:C2:20 (random)
  I: HCI: version 5.2 (0x0b) revision 0x125b, manufacturer 0x0059
  I: LMP: version 5.2 (0x0b) subver 0x125b
  DM Bluetooth LE Synchronization initialization
  
  Measurement result:
        Addr CF:4E:38:D5:C0:ED (random)
        Quality ok
        Distance estimates: rtt: rtt=1.75
  
  Measurement result:
        Addr CF:4E:38:D5:C0:ED (random)
        Quality ok
        Distance estimates: rtt: rtt=1.70
  
  Measurement result:
        Addr DB:49:E9:62:DF:6D (random)
        Quality ok
        Distance estimates: rtt: rtt=2.75
  

Dependencies

This sample uses the following nRF Connect SDK subsystems:

• Direction and Distance Finding Service (DDFS)

• DK Buttons and LEDs

This sample uses the following sdk-nrfxlib library:

• Nordic Distance Measurement library

In addition, it uses the following Zephyr libraries:

• Kernel Services:

  • include/kernel.h

• Pulse Width Modulation (PWM):

  • drivers/pwm.h

• include/sys/printk.h

• include/sys/byteorder.h

• include/random/random.h

• API:

  • include/bluetooth/bluetooth.h

  • include/bluetooth/scan.h

• ext/hal/nordic/nrfx/hal/nrf_radio.h