nPM1300: One button
The One button sample demonstrates how to support wake-up, shutdown, and user interactions of nPM1300 using a single button on a compatible development kit that is connected to the PMIC.
Requirements
The sample supports the following development kits:
Hardware platforms |
PCA |
Board name |
Board target |
|---|---|---|---|
PCA10090 |
|
||
PCA10156 |
|
||
PCA10175 |
|
||
PCA10095 |
|
||
PCA10040 |
|
||
PCA10056 |
|
The sample also requires an nPM1300 EK that you need to connect to the development kit as described in Wiring.
Overview
The nPM1300’s SHPHLD/RESET button controls the device state. The sample controls an LED, load switch and nPM1300 power mode based on button press duration.
The nPM1300’s GPIO3 pin is configured as an interrupt output, and is used to signal button press and USB detection events to the host.
Wiring
To connect your DK to the nPM1300 EK, complete the following steps:
Make the following connections on the nPM1300 EK:
Remove all existing connections.
On the P1 pin header, connect VBATIN and VBAT pins with a jumper.
On the P13 pin header, connect RSET1 and VSET1 pins with a jumper.
On the P14 pin header, connect RSET2 and VSET2 pins with a jumper.
On the P15 pin header, connect VOUT1 and LSIN1 pins with a jumper.
On the P17 pin header, connect HOST and LED2 pins with a jumper.
Connect a suitable battery to the J2 connector.
Connect the chosen DK to the nPM1300 EK as in the following table:
nPM1300 EK connections. nPM1300 EK pins
nRF52 DK pins
nRF52840 DK pins
nRF5340 DK pins
nRF54L15 DK pins
nRF54H20 DK pins
nRF9160 DK pins
SDA
P0.26
P0.26
P1.02
P1.11
P0.04
P0.30
SCL
P0.27
P0.27
P1.03
P1.12
P0.00
P0.31
GPIO3
P0.22
P1.12
P1.12
P1.10
P0.05
P0.10
VDDIO
VDD
VDD
VDD
VDDIO
VDD_P0
VDD
GND
GND
GND
GND
GND
GND
GND
Note
When using the nRF54L15 DK, the nPM1300 GPIO3 interrupt pin assignment uses the DK’s LED 1 pin.
Building and running
This sample can be found under samples/pmic/native/npm1300_one_button in the nRF Connect SDK folder structure.
To build the sample, follow the instructions in Building an application for your preferred building environment. See also Programming an application for programming steps and Testing and optimization for general information about testing and debugging in the nRF Connect SDK.
Note
When building repository applications in the SDK repositories, building with sysbuild is enabled by default.
If you work with out-of-tree freestanding applications, you need to manually pass the --sysbuild parameter to every build command or configure west to always use it.
Testing
After programming the sample to your development kit, complete the following steps to test it:
Connect the kit to the computer using a USB cable. The kit is assigned a COM port (Windows) or ttyACM device (Linux), which is visible in the Device Manager.
Connect to the kit with a terminal emulator (for example, nRF Connect Serial Terminal). See Testing and optimization for the required settings and steps.
If the initialization was successful, the terminal displays the following message with status information:
PMIC device ok
Different length button presses:
Duration
Log output
Outcome
< 1 sec
Short press
Sample flashes LED at 5 Hz, LDSW 1 enabled
1 - 5 sec
Medium press
Sample flashes LED at 1 Hz, LDSW 1 disabled
5 - 10 sec
Long press
nPM1300 enters ship mode provided J3 is not connected
> 10 sec
None
nPM1300 long press reset activates
Ship mode is the lowest power state of the nPM1300. To exit ship mode, press the SHPHLD button or attach a USB cable to J3. In a production design, this will power off any device that is powered from an nPM1300 output.
The long press reset performs a full power cycle of the nPM1300 and resets all setting to powerup defaults. In a production design, this will reset any device that is powered from an nPM1300 output.
When using a separately powered development kit, you must restart the application to reconfigure the nPM1300 after exiting ship mode or long press reset.
Dependencies
The sample uses the following Zephyr libraries: